1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1

Ductile iron, double volute casing with investment cast 304SS impeller & 250# RF suction and discharge flanges

2

Horizontally split with pry-bar locations & jackscrews for easy rotor access

3

304 stainless steel acorn nuts fully enclose the casing studs to minimize corrosion

4

Purge grease lubricated 6300 series, deep grove ball bearings at the inboard & outboard locations allowing bearing housing removal and replacement without complete pump disassembly

5

Rigid coupling guards are located at both stuffing box locations

6

Dedicated ductile iron mounting plate bolted to put to easily view 304 stainless steel nameplate

7

All 304 stainless steel ball valves and flush tubing ensuring adequate lubrication to both stuffing boxes

8

304 stainless steel flush lines and ball valves provide lubrication to both stuffing boxes

9

Leakage from both stuffing boxes are plumbed to a single point making the connection to the drain very easy

10

Milled and drilled pump pad locations to ensure complete contact and no soft foot issues

11

Rigid coupling guard completely surrounds the coupling and shaft

12

Fabricated base provided with jackscrews to aid in motor alignment

13

Integral grounding lug for the complete base assembly

14

Base jackscrews allow for very easy base leveling during installation

15

Integral lifting lugs to safely lift and move the complete base assembly

16

Electric motor or Diesel engine driver available

17

Leakage from the mounted air release valve is ported to the stuffing box drain keeping the pump clean

Series 5030 SC

Split Case Pumps

FEATURES & BENEFITS

The Series 5030 SC Split Case product line is a third party certified, fire protection pump in a flex-coupled orientation with an axially split casing assembly.  This product can be electrically or Diesel engine driven and is a perfect fit for the smaller and larger flow applications found throughout the industry.

Certified Performance:

Flows:  300 GPM to 8,000 GPM [68 M3/HR To 1,817 M3/HR]
Heads:  40 PSI to 367 PSI [2.75 BAR to 25.3 BAR]
Speeds:  3550 RPM, 2950 RPM, 2600 RPM, 2350 RPM, 2100 RPM, 2000 RPM, 1760 RPM, 1480 RPM

The 5030 Series SC Split Case product line has the following specifiable features and benefits:

  • Ductile iron, ribbed casing with 400 PSI pressure ratings
  • Double volute casing designed to reduce radial loads
  • 250# RF suction & 250# RF discharge flanges
  • High efficiency impeller design that leads the industry on lower horsepower
  • Investment cast, 304 stainless steel impeller
  • 420 stainless steel shafting
  • 304 stainless steel shaft sleeves, 304 stainless steel glands and 304 stainless steel lantern rings
  • 304 stainless steel flush lines with 304 stainless steel ball valves
  • 6300 series deep groove bearing at the inboard and outboard locations
  • Modular rotating assembly groups minimizes number of parts needed
  • Inboard & outboard bearing housings are removable and replaceable without removing the casing top
  • Casing top has pry bar locations and jackscrews to aid in pump disassembly
  • Full optional metallurgy support for sea water applications (all bronze, all 2205 & all 2507 super duplex stainless steel)
  • Milled and drilled pad locations under pump and driver
  • Alignment jackscrews located under the motor (Electric) or pump (Diesel) to aid in field alignment
  • Base leveling jackscrews to allow for a quick and efficient leveling of the base to the concrete pad in the field
  • Two grounding lugs located on the base to safely ground the entire assembly
  • Integral lifting lugs on the base to safely lift and transport the entire base assembly